yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@102 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


77B Oiles Glitron F Bushings `50 C0.8 ƒÓd `6 C0.3 `18 C0.5 6.3 i @j chamfer Motion direction Mating shaft Bushing Housing H7 ƒÓd ƒÓD h6 0.8 i @j L ƒÓd a a a a a: Chamferingimmj a ƒÓD Specify Part No. by required I.D. and length. (e.g.) I.D. is 9mm and length is 10mm. 77B - 0910 L I.D. O.D. ƒÓd Tolerance ƒÓD Tolerance I.D. tolerance after press fitting (reference) 3456789 10 12 15 16 17 18 20 25 30 40 50 6789 11 12 13 14 16 21 22 23 24 26 31 36 48 60 6 0406 0506 0606 3 0303 5 0305 0405 0505 0605 8 0408 0508 0608 0708 0808 1008 10 0510 0610 0810 0910 1010 1210 1510 15 0815 1015 1215 1515 1615 1715 1815 2015 20 1220 1520 1620 1820 2020 2520 3020 25 1625 2025 2525 3025 {0.133 {0.133 {0.133 {0.136 {0.148 {0.152 {0.155 {0.165 {0.168 {0.170 {0.170 {0.180 {0.180 {0.190 {0.190 {0.190 {0.200 {0.210 {0.183 {0.183 {0.183 {0.186 {0.198 {0.202 {0.205 {0.215 {0.218 {0.240 {0.240 {0.250 {0.250 {0.310 {0.310 {0.310 {0.340 {0.350 {0.04 {0.04 {0.04 {0.04 {0.05 {0.05 {0.05 {0.05 {0.05 {0.05 {0.05 {0.05 {0.05 {0.06 {0.06 {0.06 {0.06 {0.06 {0.09 {0.09 {0.09 {0.09 {0.10 {0.10 {0.10 {0.10 {0.10 {0.10 {0.10 {0.10 {0.10 {0.11 {0.11 {0.11 {0.11 {0.11 {0.074 {0.076 {0.076 {0.079 {0.082 {0.086 {0.089 {0.099 {0.102 {0.106 {0.106 {0.116 {0.116 {0.116 {0.118 {0.118 {0.128 {0.140 Length L@Tolerance 0 @|0.25 30 2030 2530 3030 4030 40 4040 5040 50 5050 {0.124 {0.126 {0.126 {0.129 {0.132 {0.136 {0.139 {0.149 {0.152 {0.176 {0.176 {0.186 {0.186 {0.236 {0.238 {0.238 {0.268 {0.280 iš 0 @|0.2 j š š š š š š š Parts No. The dimensional tolerances are the values measured at +25Ž. 101Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter