yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@111 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


GEF Oiles Glitron SE Flange Bushings 6 7 8 9 12 14 16 19 20 25 30 35 Specify Part No. by required I.D., O.D. and Length. (e.g.) I.D. is 10mm, O.D. is 14mm, and length is 8mm. GEF - 1008 I.D.¦ O.D. Flange ƒÓd Tolerance ƒÓD Tolerance Tolerance Tolerance 3 4 5 6 8 10 12 15 16 20 25 30 t 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0 2.5 2.5 2.5 ƒÓF 9 10 11 12 16 18 20 23 24 30 35 40 Tolerance 4 4 5 5 6 8 8 10 10 12 15 20 Length L GEF-0304 GEF-0404 GEF-0505 GEF-0605 GEF-0806 GEF-1008 GEF-1208 GEF-1510 GEF-1610 GEF-2012 GEF-2515 GEF-3020 Parts No. ¦The inner diameter tolerances are the values after pressing into a ring gauge of ƒÓD }0.002. L Motion direction Mating shaft Bushing ƒÓF ƒÓd ƒÓD Housing t g6 H7 6.3 i @j 0.8 i @j Type A A A C A A B B B B B B a 3.0 3.5 4.0 4.5 5.5 6.5 7.5 9.0 9.5 11.5 14.0 16.5 {0.070 {0.070 {0.070 {0.070 {0.075 {0.095 {0.100 {0.100 {0.100 {0.110 {0.110 {0.130 {0.040 {0.040 {0.040 {0.040 {0.040 {0.060 {0.060 {0.060 {0.060 {0.060 {0.060 {0.060 {0.052 {0.055 {0.055 {0.055 {0.068 {0.068 {0.068 {0.068 {0.071 {0.081 {0.081 {0.095 {0.012 {0.015 {0.015 {0.015 {0.018 {0.018 {0.018 {0.018 {0.021 {0.021 {0.021 {0.025 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.15 |0.15 |0.15 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.15 |0.20 |0.20 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 @0 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.10 |0.15 |0.15 |0.20 Type A a R 2 Type C a a 2-R CAV NO. 2-2 Type B a 3-R 3-2 L C0.3 2-C0.3 R0.1 or less ƒÓF ƒÓd ƒÓD t 0.3 Parts No. The dimensional tolerances are the values measured at +25Ž. 110 Selection Guide Product Information Plastic Bearing Multi-layer Bearing Metallic Bearing Air Bearings Technical Slide Shifter Information Corporate Profi le