yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@152 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


LFB Oiles Drymet LF Bushings (I.D. ƒÓ3`ƒÓ28) ¦The joint causes no influences upon rotation of the shaft. Be careful when press-fitting so that the joint is not @at the position to which the maximum load is applied. Shaft Housing I.D. O.D. Size Tolerance ƒÓd ƒÓD Tolerance 3456789 10 12 13 14 15 16 17 18 19 20 22 24 25 26 28 |0.034 |0.037 |0.037 |0.037 |0.040 |0.040 |0.040 |0.040 |0.043 |0.043 |0.043 |0.043 |0.043 |0.043 |0.043 |0.046 |0.046 |0.046 |0.046 |0.046 |0.046 |0.046 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 56789 10 11 12 14 15 16 17 18 19 20 22 23 25 27 28 30 32 56789 10 11 12 14 15 16 17 18 19 20 22 23 25 27 28 30 32 3456789 10 12 13 14 15 16 17 18 19 20 22 24 25 26 28 {0.012 {0.012 {0.015 {0.015 {0.015 {0.015 {0.018 {0.018 {0.018 {0.018 {0.018 {0.018 {0.018 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.025 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 {0.017 {0.017 {0.025 {0.025 {0.025 {0.025 {0.030 {0.030 {0.030 {0.030 {0.035 {0.035 {0.035 {0.035 {0.040 {0.040 {0.045 {0.045 {0.045 {0.050 {0.050 {0.050 {0.047 {0.047 {0.055 {0.055 {0.055 {0.055 {0.060 {0.060 {0.060 {0.060 {0.065 {0.065 {0.070 {0.070 {0.075 {0.075 {0.080 {0.080 {0.080 {0.085 {0.085 {0.090 3 4 5 6 7 8 0303 0403 0503 0603 0304 0404 0504 0604 0305 0405 0505 0605 0705 0805 0306 0406 0506 0606 0706 0806 0906 1006 1206 0607 0707 0807 1007 0408 0508 0608 0708 0808 1008 1208 1308 1408 1508 L Motion direction Bushing ƒÓd ƒÓD joint¦ 6.3 i @j chamfer Housing H7 Mating shaft Shaft 0.8 i @j ¦Outer diameter is measrued by exclusive gauge. ¦The I.D. tolerance after press fitting is for reference only. ¦I.D. ƒÓ30`ƒÓ160 are shown on pages 153 to 154. Length L@Tolerance 0 |0.3 Specify Part No. by required I.D. and length. (e.g.) I.D. is 15mm and length is 8mm. LFB - 1508 Size H7 Tolerance thick bushingT Wall thickness T Tolerance 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.5 1.5 1.5 1.5 1.5 2.0 2.0 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Parts No. 151Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter