yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@154 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


LFB Oiles Drymet LF Bushings (I.D. ƒÓ30`ƒÓ160) Housing I.D. O.D. H7 ƒÓd ƒÓD Tolerance 30 31 32 35 38 40 45 50 55 60 65 70 75 80 85 90 100 110 120 130 140 150 160 |0.046 |0.050 |0.050 |0.050 |0.050 |0.050 |0.050 |0.050 |0.055 |0.055 {0.005 {0.005 {0.005 {0.005 0 0 0 0 0 |0.005 |0.005 |0.005 |0.005 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 |0.025 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 {0.035 34 35 36 39 42 44 50 55 60 65 70 75 80 85 90 95 105 115 125 135 145 155 165 34 35 36 39 42 44 50 55 60 65 70 75 80 85 90 95 105 115 125 135 145 155 165 30 31 32 35 38 40 45 50 55 60 65 70 75 80 85 90 100 110 120 130 140 150 160 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.030 {0.030 {0.030 {0.030 {0.030 {0.030 {0.035 {0.035 {0.035 {0.035 {0.035 {0.040 {0.040 {0.040 {0.040 {0.040 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 {0.050 {0.050 {0.050 {0.055 {0.055 {0.055 {0.060 {0.060 {0.065 {0.070 {0.075 {0.075 {0.075 {0.075 {0.075 {0.075 {0.080 {0.080 {0.090 {0.090 {0.100 {0.120 {0.120 {0.090 {0.090 {0.090 {0.095 {0.095 {0.095 {0.100 {0.105 {0.110 {0.120 {0.125 {0.125 {0.130 {0.130 {0.130 {0.130 {0.140 {0.140 {0.145 {0.145 {0.165 {0.185 {0.185 12 15 20 25 30 35 3015 3115 3215 3515 4015 3012 3512 4012 3020 3220 3520 3820 4020 4520 5020 3025 3125 3225 3525 3825 4025 4525 5025 5525 3030 3130 3230 3530 3830 4030 4530 5030 5530 6030 6530 7030 7530 3035 3535 3835 4035 4535 5035 5535 6035 7035 7535 Length L@Tolerance 0 |0.3 ¦Outer diameter is measrued by exclusive gauge. ¦The I.D. tolerance after press fitting is for reference only. ¦I.D. ƒÓ3`ƒÓ28 are shown on pages 151 to 152. Specify Part No. by required I.D. and length. (e.g.) I.D. is 70mm and length is 35mm. LFB - 7035 ¦The joint causes no influences upon rotation of the shaft. Be careful when press-fitting so that the joint is not @at the position to which the maximum load is applied. L Motion direction Bushing ƒÓd ƒÓD joint¦ 6.3 i @j chamfer Housing H7 Mating shaft Shaft 0.8 i @j wall thicknessT Shaft Size Tolerance H7 Tolerance Wall thickness T Tolerance 2.0 2.0 2.0 2.0 2.0 2.0 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.040 |0.040 |0.040 |0.040 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 |0.080 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ 0@ |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 |0.030 Parts No. 153Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter