yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@184 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


SPB Oiles 500SP1 SL1 Bushings (I.D. ƒÓ6`ƒÓ45) I.D. O.D. ƒÓd Tolerance ƒÓD Tolerance 8 10 12 15 16 19 20 {0.010 {0.013 {0.013 {0.016 {0.016 {0.016 {0.016 {0.016 {0.016 {0.016 {0.020 {0.020 {0.020 {0.020 {0.020 {0.020 {0.020 {0.020 {0.020 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.022 {0.028 {0.028 {0.034 {0.034 {0.034 {0.034 {0.034 {0.034 {0.034 {0.041 {0.041 {0.041 {0.041 {0.041 {0.041 {0.041 {0.041 {0.041 {0.050 {0.050 {0.050 {0.050 {0.050 {0.050 {0.050 {0.050 {0.050 {0.050 10 12 14 18 19 20 21 22 23 24 26 28 30 32 33 35 38 38 40 40 42 44 45 48 50 55 55 56 60 {0.015 {0.018 {0.018 {0.018 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.025 {0.030 {0.030 {0.030 {0.030 {0.006 {0.007 {0.007 {0.007 {0.008 {0.008 {0.008 {0.008 {0.008 {0.008 {0.008 {0.008 {0.008 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.009 {0.011 {0.011 {0.011 {0.011 061008 081208 101408 121808 6 8 10 12 13 14 15 16 17 18 19 20 20 22 25 25 28 30 30 31.5 32 35 35 38 40 40 45 45 45 061010 081210 101410 121810 131910 142010 152110 162210 182410 202810 203010 061012 081212 101412 121812 131912 142012 152112 162212 182412 202812 203012 223212 253312 253512 303812 304012 081215 101415 121815 131915 142015 152115 162215 172315 182415 192615 202815 203015 223215 253315 253515 303815 304015 405015 405515 121816 152116 162216 182416 202816 203016 253316 253516 121819 162219 202819 101420 121820 131920 142020 152120 162220 182420 192620 202820 203020 223220 253320 253520 283820 303820 304020 324220 354420 354520 405020 121825 131925 142025 152125 162225 182425 202825 203025 223225 253325 253525 283825 303825 304025 354425 354525 405025 25 ¦The I.D. tolerance after press fitting is for reference only. ¦I.D. ƒÓ50`ƒÓ200 are shown on pages 185 to 186. Length L@Tolerance |0.1 |0.3 Motion direction Mating shaft Bushing ƒÓd ƒÓD Shaft d8: For general ( High-load) e7: For general (Low-load) f7: For high accuracy L 1.6 i @j Shaft Specify Part No. by required I.D., O.D. and Length. (e.g.) I.D. is 25mm, O.D. is 33mm, and length is 20mm. SPB - 253320 6.3 i @j chamfer Housing H7 All SPB bushings have engraved goilesh mark. Parts No. The dimensional tolerances are the values measured at +25Ž. 183Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter