yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@185 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


30 35 40 50 60 70 80 SPW Washer I.D. ƒÓd 0603 0803 1003 1203 1303 1403 1503 1603 1803 1803 2005 2005 2505 2505 2505 3005 3005 3005 3505 3505 3505 3505 4007 4007 4007 4507 4507 4507 4507 152140 162240 182440 202840 203040 253340 253540 283840 303840 304040 314040 324240 354440 354540 384840 405040 405540 455540 455640 456040 202850 203050 253350 253550 303850 304050 354450 354550 405050 405550 455550 455650 456050 253360 253560 303860 304060 354460 354560 405060 405560 455560 455660 456060 405070 456070 405080 456080 121830 131930 142030 152130 162230 182430 202830 203030 253330 253530 283830 303830 304030 314030 324230 354430 354530 405030 405530 455530 455630 456030 152135 162235 182435 202835 203035 253335 253535 303835 304035 354435 354535 405035 405535 455535 455635 456035 š š š š š š š š š š š š {0.019 {0.025 {0.025 {0.031 {0.030 {0.030 {0.030 {0.030 {0.030 {0.030 {0.037 {0.037 {0.037 {0.037 {0.037 {0.037 {0.037 {0.037 {0.037 {0.046 {0.046 {0.046 {0.046 {0.046 {0.046 {0.045 {0.045 {0.045 {0.045 {0.007 {0.010 {0.010 {0.013 {0.012 {0.012 {0.012 {0.012 {0.012 {0.012 {0.016 {0.016 {0.016 {0.016 {0.016 {0.016 {0.016 {0.016 {0.016 {0.021 {0.021 {0.021 {0.021 {0.021 {0.021 {0.020 {0.020 {0.020 {0.020 Length L@Tolerance |0.1 |0.3 SPW SPB Use this product together with the Oiles #500SP washer (SPW shown on page 193) in a position where thrust loads are applied. ¦Be sure to determine the position with a countersunk head screw and fix when the SPW with š shown in the table below is used, since the inner diameter is larger than the shaft diameter. Set screw Set screw œ Applicable to rotation, oscillation, and reciprocating motion. œ Do not use this under water. œ 31.5mm I.D bushing can be used as an intermediate trunnion bushing for hydraulic cylinders. 15‹ 10‹ R1`2 C0.3`0.5 L 0`4.5 ƒÓdF7 ƒÓDm6 1`2.5 1.6 1.6 I.D. tolerance after press fitting (reference) 6 8 10 12 13 14 15 16 17 18 19 20 20 22 25 25 28 30 30 31.5 32 35 35 38 40 40 45 45 45 It is recommended to use a set screw to prevent dislocation. 184 Selection Guide Product Information Plastic Bearing Multi-layer Bearing Metallic Bearing Air Bearings Technical Slide Shifter Information Corporate Profi le