yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@188 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


SPBL Oiles 500SP1 SL4 Bushings I.D. O.D. ƒÓd Tolerance ƒÓD Tolerance 12 15 16 18 20 25 30 35 40 40 45 50 50 55 60 65 70 75 80 90 100 110 120 130 140 150 160 170 180 190 200 18 21 22 24 30 35 40 45 50 55 60 60 65 70 75 80 90 95 100 110 120 130 140 150 160 170 180 190 200 210 230 {0.032 {0.032 {0.032 {0.032 {0.040 {0.040 {0.040 {0.050 {0.050 {0.050 {0.050 {0.050 {0.050 {0.060 {0.060 {0.060 {0.060 {0.060 {0.060 {0.072 {0.072 {0.072 {0.072 {0.085 {0.085 {0.085 {0.085 {0.085 {0.085 {0.100 {0.100 {0.050 {0.050 {0.050 {0.050 {0.061 {0.061 {0.061 {0.075 {0.075 {0.075 {0.075 {0.075 {0.075 {0.090 {0.090 {0.090 {0.090 {0.090 {0.090 {0.107 {0.107 {0.107 {0.107 {0.125 {0.125 {0.125 {0.125 {0.125 {0.125 {0.146 {0.146 {0.034 {0.041 {0.041 {0.041 {0.041 {0.050 {0.050 {0.050 {0.050 {0.060 {0.060 {0.060 {0.060 {0.062 {0.062 {0.062 {0.073 {0.073 {0.073 {0.076 {0.076 {0.088 {0.088 {0.090 {0.090 {0.093 {0.093 {0.106 {0.106 {0.109 {0.113 {0.023 {0.028 {0.028 {0.028 {0.028 {0.034 {0.034 {0.034 {0.034 {0.041 {0.041 {0.041 {0.041 {0.043 {0.043 {0.043 {0.051 {0.051 {0.051 {0.054 {0.054 {0.063 {0.063 {0.065 {0.065 {0.068 {0.068 {0.077 {0.077 {0.080 {0.084 20 25 30 35 40 50 60 70 253525 304025 121820 152120 162220 182420 203020 253520 304020 354520 162230 203030 253530 304030 354530 405030 456030 354535 203040 253540 304040 354540 405040 405540 506040 506540 557040 253550 304050 354550 405050 405550 456050 506050 506550 607550 354560 405060 405560 456060 506060 506560 557060 607560 658060 709060 8010060 9011060 10012060 506570 557070 607570 658070 709070 759570 80 607580 658080 709080 8010080 9011080 10012080 12014080 ¦Part No. with – are made-to-order. ¦The I.D. tolerance after press fitting is for reference only. L 1.6 i @j Shaft ƒÓd ƒÓD Housing H7 chamfer 6.3 i @j Mating shaft Bushing Shaft d8: For general b9: For high-load, underwater, and under seawater use Motion direction Length L@Tolerance |0.1 |0.3 Parts No. Specify Part No. by required I.D., O.D. and Length. (e.g.) I.D. is 60mm, O.D. is 75mm, and length is 80mm. SPBL - 607580 ¦Operating Temperature Range: |40` {80‹C (|40` {176‹F) Solid Lubricant : SL464 (refer to page 36) The dimensional tolerances are the values measured at +25Ž. 187Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter