yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@192 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


SPFG Oiles 500SP1 SL1 Thrust Bushings 20 25 30 35 40 45 50 55 65 70 90 110 120 140 6.3 i @j chamfer Housing H7 Motion direction Mating shaft Flange bushing ƒÓF ƒÓd ƒÓD Shaft d8: For general (high-load) e7: For general (low-load) f7: For high accuracy g6: For high accuracy (intermittent operation) 1.6 i @j Shaft L t Specify Part No. by required I.D. and Length. (e.g.) I.D. is 35mm and length is 25mm. Parts No. SPFG - 3525 I.D. O.D. Flange ƒÓd Tolerance ƒÓD Tolerance ƒÓF Tolerance t Tolerance 18 20 23 25 68 10 12 13 15 16 18 20 25 30 35 40 50 60 70 80 10 12 14 18 19 21 22 24 28 33 38 44 50 62 74 85 96 333333335555788 10 10 20 25 25 30 30 35 35 40 45 50 55 65 70 90 110 120 140 {0.019 {0.023 {0.023 {0.023 {0.028 {0.028 {0.028 {0.028 {0.028 {0.034 {0.034 {0.034 {0.034 {0.041 {0.043 {0.051 {0.051 {0.028 {0.034 {0.034 {0.034 {0.041 {0.041 {0.041 {0.041 {0.041 {0.050 {0.050 {0.050 {0.050 {0.060 {0.062 {0.073 {0.073 {0.020 {0.025 {0.025 {0.032 {0.032 {0.032 {0.032 {0.032 {0.040 {0.040 {0.040 {0.050 {0.050 {0.050 {0.060 {0.060 {0.060 {0.032 {0.040 {0.040 {0.050 {0.050 {0.050 {0.050 {0.050 {0.061 {0.061 {0.061 {0.075 {0.075 {0.075 {0.090 {0.090 {0.090 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.03 |0.04 |0.04 |0.04 |0.04 11 0611 1211 13 0813 1013 1313 1513 1613 1018 1218 1318 1518 1618 1818 2020 2520 3020 3520 1223 1323 1523 1623 1823 2025 2525 3025 3525 ¦The I.D. tolerance after press fitting is for reference only. Length L |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 The dimensional tolerances are the values measured at +25Ž. 191Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter