yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@262 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


30F Oiles 300 Flange Bushings a b c: Chamferingi mmj ƒÓd `22 C0.5 `60 C1.5 `50 C1 ƒÓd `22 R0.3 `60 R1 `50 R0.5 ƒÓd `22 C0.3 `60 C0.5 I.D. O.D. Flange ƒÓd Tolerance ƒÓD Tolerance ƒÓF t Tolerance 5 568 10 12 14 15 16 18 20 22 25 28 30 32 35 40 45 50 55 60 8 10 12 16 18 20 21 22 25 28 30 35 38 40 42 45 50 55 60 70 75 1.5 2 2 3 3333 3.5 4 4 5 5555555 7.5 7.5 11 14 20 23 25 27 28 29 33 38 40 45 48 50 52 60 65 70 75 85 90 {0.040 {0.040 {0.046 {0.046 {0.041 {0.041 {0.041 {0.041 {0.041 {0.055 {0.055 {0.055 {0.055 {0.055 {0.073 {0.073 {0.073 {0.073 {0.073 {0.098 {0.098 {0.058 {0.058 {0.068 {0.068 {0.068 {0.068 {0.068 {0.068 {0.068 {0.088 {0.088 {0.088 {0.088 {0.088 {0.112 {0.112 {0.112 {0.112 {0.112 {0.144 {0.144 8 10 12 15 20 25 30 40 50 60 80 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.1 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 |0.3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Tolerance 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Parts No. Specify Part No. by required I.D. and length. (e.g.) I.D. is 30mm and length is 40mm. 30F - 3040 {0.030 {0.030 {0.034 {0.045 {0.045 {0.040 {0.040 {0.040 {0.040 {0.060 {0.060 {0.054 {0.054 {0.054 {0.078 {0.078 {0.078 {0.070 {0.070 {0.102 {0.102 Length L@Tolerance 0 |0.3 Motion direction Mating shaft Flange bushing L 6.3 i @j chamfer Housing H7 t 1.6 i @j h7 ƒÓF ƒÓd ƒÓD b c a I.D. tolerance after press fitting (reference) Chamfering for the bush length of 5 and 6mm are C0.3 ƒÓd ƒÓD ƒÓF C C L t a c b 1`2 20‹ {0.019 {0.019 {0.023 {0.023 {0.023 {0.028 {0.028 {0.028 {0.028 {0.028 {0.028 {0.034 {0.034 {0.034 {0.034 {0.034 {0.034 {0.041 {0.041 {0.041 {0.041 {0.012 {0.012 {0.012 {0.023 {0.018 {0.013 {0.013 {0.013 {0.013 {0.027 {0.027 {0.021 {0.021 {0.021 {0.039 {0.039 {0.039 {0.031 {0.031 {0.056 {0.056 œUse Oiles 300 in lubrication oil or with periodic lubrication. 0505 0508 0608 0610 0810 1010 1210 1410 1510 0812 1012 1212 1412 1512 1612 0815 1015 1215 1415 1515 1615 1815 2015 2215 2515 1020 1220 1420 1520 1620 1820 2020 2220 2520 1225 1425 1525 1625 1825 2025 2225 2525 2825 1530 1630 1830 2030 2230 2530 2830 3030 3230 3530 2040 2240 2540 3040 3240 3540 4040 4540 4050 4550 5050 5550 5060 5560 6060 6080 ¦The I.D. tolerance after press fitting is for reference only. {0.034 {0.034 {0.041 {0.041 {0.041 {0.049 {0.049 {0.049 {0.049 {0.049 {0.049 {0.059 {0.059 {0.059 {0.059 {0.059 {0.059 {0.073 {0.073 {0.073 {0.073 The dimensional tolerances are the values measured at +25Ž. 261Selection Guide Product Air Bearings Metallic Bearing Multi-layer Bearing Plastic Bearing Information Technical Corporate Profi le Information Slide Shifter