yDO!BOOKEƒy[ƒWƒŠƒ“ƒNz
bearing@@@87 / 392

BOOK‚ð‚Ý‚é

10•bŒã‚ÉBOOK‚̃y[ƒW‚Ɉړ®‚µ‚Ü‚·


LES Oiles Lutech E-02 Snap-fit Bushings LEM Oiles Lutech E Bar Stock Specify Part No. by required diameter. (e.g.) Diameter is 31.5mm. LEM - 30 œThe both sides of the outer diameter are cut. I.D. O.D. Flange Length ƒÓd ToleranceƒÓD1 Tolerance L Tolerance 10 10 10 12 12 12 {0.05 {0.05 {0.05 {0.05 {0.05 {0.05 0 0 0 0 0 0 W1 Tolerance 999 10 10 10 W2 Tolerance 0.8 1.2 1.6 1.2 1.6 2.0 |0.06 |0.06 |0.06 |0.06 |0.06 |0.06 |0.01 |0.01 |0.01 |0.01 |0.01 |0.01 ƒÓF 12 12 12 14 14 14 }0.2 }0.2 }0.2 }0.2 }0.2 }0.2 Parts No. LES-0608 LES-0612 LES-0616 LES-0812 LES-0816 LES-0820 666777 666888 ƒÓD2 MAX. 9.9 9.9 9.9 11.9 11.9 11.9 ƒÓD3 Tolerance 11 11 11 13 13 13 ƒÓD4 10 10 10 12 12 12 {0.1 {0.1 {0.1 {0.1 {0.1 {0.1 0 0 0 0 0 0 {0.2 {0.2 {0.2 {0.2 {0.2 {0.2 {0.1 {0.1 {0.1 {0.1 {0.1 {0.1 |0.049 |0.049 |0.049 |0.049 |0.049 |0.049 |0.013 |0.013 |0.013 |0.013 |0.013 |0.013 Diameter Length Parts No. ƒÓD L 21.5 31.5 41.5 52 500 500 500 500 LEM-20 LEM-30 LEM-40 LEM-50 Tolerance }0.4 }0.4 }0.5 L }0.5 ƒÓD ƒÓF C0.3 C0.3 ƒÓD2MAX. ƒÓD3 W2 1.5}0.05 L Section B-B A ƒÓD4 ƒÓd Specify Part No. by required I.D. and W2 dimension. (e.g.) I.D. is 6mm and W2 dimention is 1.6mm. LES - 0616 ƒÓD1 W1  ƒÓ0.05 A B B ¦The recommended clearance is 0.030 to 0.095 mm for each dimension. ¦When used in a hole made in a sheet-metal, the snap fit is scraped by burrs made when punching. It is recommended to remove burrs @with a grinder before use. ƒÓDh and Wh are recommended mating hole dimension. ¡How to assemble into housing. Prevent from falling off. Wh {0.037 |0.013 ƒÓD h {0.04 |0.01 Parts No. Parts No. The dimensional tolerances are the values measured at +25Ž. 86 Selection Guide Product Information Plastic Bearing Multi-layer Bearing Metallic Bearing Air Bearings Technical Slide Shifter Information Corporate Profi le